Jewelry Adhesive CG 610 – 2K Epoxy for Crystals

✔ 2C epoxy resin adhesive for jewelry and crystals
✔ Ideal for small crystals (PP0–PP14)
✔ Low viscosity for precise application
✔ Strong bonding on metal, glass, plastic and more
✔ Resistant to sweat, perfume and moisture
✔ Suitable for DIY and professional use
✔ 140 min processing time - 48 h curing time

€10.95

Content: 0.05 Liter (€219.00 / 1 Liter)

Available, delivery time: Instant download

Product number: SW10017

AP CG 610 Epoxy Resin Glue

Strong for small crystals.

CG 610 is a 2C epoxy resin and specially developed for bonding small crystals. The Swarovski crystal sizes PP0 to PP14 are ideally suited. CG 610 has optimal adhesion properties when bonding to metal, glass, crystal, bondable plastic, rubber, wood, cork and porcelain. Due to its low viscosity, even small quantities can be applied very easily. Compared to CG 500, the adhesive is thinner and is slightly more stable when cured. Special properties of the adhesive are its chemical resistance to perspiration, perfume and moisture, as well as strong adhesion and impact-resistant mechanical properties. The product is completely non-toxic and is not a dangerous good.

Rely on over 10 years of application experience in industry and DIY.

Technical data:

Mixing ratio	100 : 50 (volume)
Mixing ratio	100 : 48 (weight)
Viscosity (mixture)	1.750 ± 250 mPa*s
Pot life 23°C	140 min

Handling stability 23°C	24 h
Curing time 23°C	72 h
Curing time 40°C	18 h
Curing time 100°C	1,5 h

Scope of delivery:

50 mL adhesive catridge (16,7 mL hardener & 33,3 mL epoxy resin), 2 mixing tubes

Application

1. Check surface tension

Before starting the application of the adhesive, the suitability of the surface needs to be checked. The required surface tension measurement can be carried out very easily with our Test Pen.

2. Preparing the gluing area:

For a perfect bonding result, the gluing area has to be grain- and dust-free. Therefore, clean the surface with e.g. acetone or isopropanol before application.

3. Mix the adhesive:

Remove the cartridge cap, put on the mixing tube and insert the plunger for the cartridge. The first drop that comes out of the mixing tube should not be used, as the components may not be perfectly mixed yet. The adhesive can be applied with e.g. a spatula or with the tip of the catridge now.

4. Dosage of the adhesive:

Respective of the shape of the gluing area, the glue should be applied as follows:

With a round gluing area, a dot of glue in the center is sufficient. When the crystal is applied, the glue will be evenly distributed in the gluing gap. To glue a single spot, aim the dispensing needle just above the spot to be glued and lift it slowly upwards to avoid any glue spreading out sideways.

With a square or rectangular gluing area, apply a cross of glue to ensure it is evenly spread into the corners.

5. Remove excess adhesive:

After the bonding process, the excess adhesive can be easily removed with a cotton swab soaked in a solvent (e.g. isopropanol).

Further application instructions can be found in the Swarovski Application Manual

The data given are typical average values or characteristic values determined and measured under laboratory conditions. Therefore, the data and information given do not constitute a guarantee or assurance of specific product properties or the suitability of the product for a specific application.

DANGER:

Causes skin irritation.
May cause allergic skin reactions.
Causes serious eye damage.
Harmful to aquatic life with long-lasting effects.

SAFETY INSTRUCTIONS:

Avoid breathing vapor/aerosol.
Avoid release to the environment.
Wear protective gloves and eye protection.

IF ON SKIN: Wash with plenty of water.
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing.
Immediately call a poison control center or doctor.

If skin reaction occurs: Get medical advice/attention.
Dispose of contents/container in accordance with regulations.

Hazard warning 1 Hazard warning 2

Empfohlenes Zubehör

Static mixer for 2C adhesives, pack of 10 - universally compatible

UNIVERSELL: Die Mischdüsen sind für alle gängigen 25ml und 50ml 1:1-Kartuschen von AP und vielen anderen Herstellern (Henkel, Loctite, Weicon, Würth, Berner, etc.) geeignet BESTE DURSCHMISCHUNG: Dank 18 spezieller Mischelemente werden die beiden Komponenten besonders stark durschmischt FEINE DOSIERSPITZE: Die Dosierspitze ermöglicht einen präzisen und gezielten Materialauftrag. Bei höherviskosen Materialien kann diese durch einen einfachen Schnitt vergrößert werdenTECHNISCHE DATEN: 18 Mischelemente, quattro pro Mischer, 4,2 mm Innendurchmesser, 1,7ml Volumen, Gesamtlänge 90mm, Mischungsverhältnis 1:1 LIEFERUMFANG: 10 x Mischspitzen + AP Anwendungstipps

Content: 10 Stück (€1.06 / 1 Stück)

€10.60*

Static mixer for 2C adhesives, pack of 10 - universally compatible

UNIVERSELL: Die Mischdüsen sind für alle gängigen 25ml und 50ml 1:1-Kartuschen von AP und vielen anderen Herstellern (Henkel, Loctite, Weicon, Würth, Berner, etc.) geeignet und finden speziell bei dem 2K-Schmuckklebstoff CG610 Verwendung BESTE DURSCHMISCHUNG: Dank 25 spezieller Mischelemente werden die beiden Komponenten besonders stark durschmischt FEINE DOSIERSPITZE: Die Dosierspitze ermöglicht einen präzisen und gezielten Materialauftrag. Bei höherviskosen Materialien kann diese durch einen einfachen Schnitt vergrößert werdenTECHNISCHE DATEN: 25 Mischelemente, quattro pro Mischer, 4,2 mm Innendurchmesser, 2,6ml Volumen, Gesamtlänge 122mm, Mischungsverhältnis 1:1 LIEFERUMFANG: 10 x Mischspitzen + AP Anwendungstipps

Content: 10 Stück (€1.16 / 1 Stück)

€11.60*

Static mixer HELIX M for 2C adhesives, pack of 10 - universally compatible

UNIVERSAL: the mixing nozzles are suitable for all standard 25 ml and 50 ml 1:1 cartridges from AP and many other manufacturers (Henkel, Loctite, Weicon, Würth, Berner, etc.)MATERIAL SAVING: with a waste volume of 1.04 ml, compared to the green Quattro design, 1.56 ml less waste per dosing processFINE DOSING TIP: the dosing tip allows for precise and targeted material application. For higher viscous materials, this can be enlarged by a simple cut.OPAQUE MIX: the mixing behaviour is comparable to the high-volume quattromixer and can also be ideally captured by the transparent side view.Technical data: 16 mixing elements, 4.2 mm inner diameter, 1.04 ml volumeBox contents: 10 mixing tubes + AP application tips

Content: 10 Stück (€0.75 / 1 Stück)

From €7.50*

Details